Help in finding replacement carburetor or parts - Snowblower Forum : Snow Blower Forums
 
LinkBack Thread Tools
post #1 of 8 Old 10-22-2019, 03:18 PM Thread Starter
Junior Member
 
Join Date: Jan 2018
Posts: 2
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 0
Likes (Given): 0
Likes (Received): 0
Help in finding replacement carburetor or parts

I have an Ariens model 921022 Deluxe 28 with B&S 250cc engine (model number 15C1 34 2143 F8) dating from 2011. Has been experiencing some lean surge and would like to either clean or replace the carburetor but can't find any site that recognizes this engine number or the carburetor model #799731 stamped on the carb body so that I can buy the correct parts. Carb is an original B&S with their logo molded into the carb body. Is there an updated carb number that replaces the model that I have? Thanks.
h.menkes is offline  
Sponsored Links
Advertisement
 
post #2 of 8 Old 10-22-2019, 03:49 PM
Senior Member
 
ST1100A's Avatar
 
Join Date: Feb 2015
Location: Northeast, Easton, Pa
Posts: 381
Post Thanks / Like
Thanks (Given): 35
Thanks (Received): 68
Likes (Given): 131
Likes (Received): 79
Quote:
Originally Posted by h.menkes View Post
I have an Ariens model 921022 Deluxe 28 with B&S 250cc engine (model number 15C1 34 2143 F8) dating from 2011. Has been experiencing some lean surge and would like to either clean or replace the carburetor but can't find any site that recognizes this engine number or the carburetor model #799731 stamped on the carb body so that I can buy the correct parts. Carb is an original B&S with their logo molded into the carb body. Is there an updated carb number that replaces the model that I have? Thanks.
Carb rebuild kit part# 797634
depending on the date code number there are 2 carbs available.
#594014 before date code 11080800
#504015 after date code 11080700
Engine model# is 15C134-2143-F8. If you typed the model number in wrong, it might not show up.
Possible your float needle or seat is bad causing improper float level, meaning float level too low, and that will cause a "Lean" condition/surge.
See if you can look up the 2 carb part #'s I gave you and look at the pictures of them, there are 2 different carbs, you can tell the difference when you see the pictures of them, but the rebuild/overhaul kit is the same for both.

Last edited by ST1100A; 10-22-2019 at 03:58 PM.
ST1100A is online now  
post #3 of 8 Old 10-22-2019, 04:24 PM Thread Starter
Junior Member
 
Join Date: Jan 2018
Posts: 2
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 0
Likes (Given): 0
Likes (Received): 0
Thanks for the quick reply. I didn't see a date code on the carb or the engine but the engine serial number is 1109108896123. The blower has a serial number of 061256. The 590014 carb looks like what I have. Does this look correct for this engine serial number? Thanks again.

Greendart
h.menkes is offline  
post #4 of 8 Old 10-22-2019, 06:36 PM
Senior Member
 
Join Date: Jan 2018
Location: North Dallas area and UP of MI, average snowfall 202"
Posts: 723
Post Thanks / Like
Thanks (Given): 16
Thanks (Received): 66
Likes (Given): 59
Likes (Received): 178
just get the rebuild kit and be done with it . . .
tadawson is online now  
post #5 of 8 Old 10-22-2019, 07:21 PM
Senior Member
 
enigma-2's Avatar
 
Join Date: Feb 2014
Location: Northern Indiana
Posts: 303
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 18
Likes (Given): 2
Likes (Received): 44
You might try adding a double dose of Sea Foam to your gas. Run until the Sea Foam mix is in the carb, then shut off and let it sit.
Years ago I left a snowblower sit for vcd a week and it dissolved all of the gum clogging the jets.

2014 Ariens 24" Platinum
2010 Yard Machines 600 Series, 24" w/179cc MTD engine
Toro CCR 3650 GTS
Troy Bilt 521OR w/Tecu HSSK50 engine
enigma-2 is offline  
post #6 of 8 Old 10-22-2019, 09:21 PM
Member
 
Join Date: Sep 2019
Posts: 65
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 8
Likes (Given): 0
Likes (Received): 6
Quote:
Originally Posted by enigma-2 View Post
You might try adding a double dose of Sea Foam to your gas. Run until the Sea Foam mix is in the carb, then shut off and let it sit.
Years ago I left a snowblower sit for vcd a week and it dissolved all of the gum clogging the jets.
It rarely works. The way Sea Foam cleans things is that it steams up when heated (required the engine running). Steam is what really cleaned the inside of the engine. It does not dissolve things very well. Gasoline maybe better at that, so people thought it was the Sea Foam. What made me hesitate to use Sea Foam is that it smokes way too much. The neighbors would be annoyed.
dman2 is online now  
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
Likes ST1100A liked this post
post #7 of 8 Old 10-23-2019, 01:32 PM
Senior Member
 
ST1100A's Avatar
 
Join Date: Feb 2015
Location: Northeast, Easton, Pa
Posts: 381
Post Thanks / Like
Thanks (Given): 35
Thanks (Received): 68
Likes (Given): 131
Likes (Received): 79
Quote:
Originally Posted by h.menkes View Post
Thanks for the quick reply. I didn't see a date code on the carb or the engine but the engine serial number is 1109108896123. The blower has a serial number of 061256. The 590014 carb looks like what I have. Does this look correct for this engine serial number? Thanks again.
11091088 is your date code, that is the part you need of the number you have. The other numbers are the "sequential".
The other numbers you listed earlier are the model, type, and code numbers that you need to identify the engine to get parts for it, those are the most important numbers, model-type-code, then date code because sometimes there are changes made to the base engine at different times when the engine is made.
ST1100A is online now  
post #8 of 8 Old 10-23-2019, 01:40 PM
Senior Member
 
ST1100A's Avatar
 
Join Date: Feb 2015
Location: Northeast, Easton, Pa
Posts: 381
Post Thanks / Like
Thanks (Given): 35
Thanks (Received): 68
Likes (Given): 131
Likes (Received): 79
Quote:
Originally Posted by dman2 View Post
It rarely works. The way Sea Foam cleans things is that it steams up when heated (required the engine running). Steam is what really cleaned the inside of the engine. It does not dissolve things very well. Gasoline maybe better at that, so people thought it was the Sea Foam. What made me hesitate to use Sea Foam is that it smokes way too much. The neighbors would be annoyed.
You are correct about Sea Foam. All it is, is basically a mixture of Alcohol diluted in a light oil mixture.
The oil coats metal to help prevent corrosion and the alcohol is used as the solvent.
You already have enough solvents in gasoline already, and if the gas has ethanol, that is an added solvent, so you are just adding more alcohol to the mixture that you are trying to stay away from in the first place, "Alcohol" that is.
ST1100A is online now  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Snowblower Forum : Snow Blower Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome