S620 carb spitting fuel - Snowblower Forum : Snow Blower Forums
Reply
 
LinkBack Thread Tools
post #1 of 12 Old 11-03-2017, 08:24 PM Thread Starter
Junior Member
 
Join Date: Nov 2017
Posts: 4
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 0
Likes (Given): 0
Likes (Received): 0
S620 carb spitting fuel

I have a Toro s620. Carb rebuild completed. When I go to start it after a few pulls Carb has fuel spitting out of the air intake. New Diaphragm and installed properly "f" Carb Diaphragm at the top. New o rings on high and low, used Carb cleaner when I took it apart. What else can it be? Any help would be great.
toroblaster is offline  
Sponsored Links
Advertisement
 
post #2 of 12 Old 11-03-2017, 08:33 PM
Banned
 
Join Date: Feb 2014
Location: Newington, CT
Posts: 2,029
Post Thanks / Like
Thanks (Given): 32
Thanks (Received): 92
Likes (Given): 446
Likes (Received): 148
may be to rich
43128 is offline  
post #3 of 12 Old 11-03-2017, 10:27 PM
Banned
 
Join Date: Nov 2016
Location: Glastonbury, CT
Posts: 474
Post Thanks / Like
Thanks (Given): 5
Thanks (Received): 33
Likes (Given): 28
Likes (Received): 68
Or a bad intake valve, have you previously seen the engine running?
DriverRider is offline  
post #4 of 12 Old 11-03-2017, 11:14 PM Thread Starter
Junior Member
 
Join Date: Nov 2017
Posts: 4
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 0
Likes (Given): 0
Likes (Received): 0
Thanks for the replys. I wouldn't think it's too rich I only have both high and low turned out just under 1 turn. Ran last winter but would stall under load - bought it used last winter (bad Diaphragm), but didn't have an issue with fuel leaking out of the Carb. Previous owner had the Diaphragm upside down and the high and low reversed. Corrected all these items and now I have fuel splashing out of the Carb. I put a fuel valve on it so I can get it to run if I partially close the fuel supply (have to find the sweet spot to get it to run well).
toroblaster is offline  
post #5 of 12 Old 11-04-2017, 07:48 AM
Senior Member
 
Join Date: Oct 2017
Posts: 179
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 28
Likes (Given): 5
Likes (Received): 41
Did you change the needle and seat?Make sure the seat is in right and don't get carb cleaner on the seat.
351beno is offline  
post #6 of 12 Old 11-04-2017, 10:49 AM Thread Starter
Junior Member
 
Join Date: Nov 2017
Posts: 4
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 0
Likes (Given): 0
Likes (Received): 0
New needle and seat and new o rings - cleaned Carb with all the seals removed. I am puzzled why so much fuel is getting into carb. Also tested the needle and seat and it seals well when blowing some air into it..
toroblaster is offline  
post #7 of 12 Old 11-04-2017, 10:58 AM
Senior Member
 
Join Date: Oct 2017
Posts: 179
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 28
Likes (Given): 5
Likes (Received): 41
Does it try to start? Also make sure the muffler is not plugged up with junk or fuel.
351beno is offline  
post #8 of 12 Old 11-04-2017, 11:18 AM
Banned
 
Join Date: Sep 2010
Location: Michigan
Posts: 1,585
Post Thanks / Like
Thanks (Given): 3
Thanks (Received): 158
Likes (Given): 95
Likes (Received): 302
Quote:
Originally Posted by 351beno View Post
Make sure the seat is in right and don't get carb cleaner on the seat.
Like Ben

Last edited by jtclays; 03-13-2018 at 04:26 PM.
jtclays is offline  
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
Likes Grunt liked this post
post #9 of 12 Old 11-04-2017, 11:56 AM Thread Starter
Junior Member
 
Join Date: Nov 2017
Posts: 4
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 0
Likes (Given): 0
Likes (Received): 0
I'll check the exhaust port. I have not checked the yet. The seat I made sure was in correctly. I am able to get it to idle and run at full tilt if I just partiality close the fuel valve that I put on it.
Thanks for all the ideas guys much appreciated. I'll probably try the "putting it at the curb" as a last resort. Lol.
I was thinking of soaking the Carb, would a sticky check ball cause it to flood or just not run?
Thanks.
toroblaster is offline  
post #10 of 12 Old 11-04-2017, 12:03 PM
Senior Member
 
orangputeh's Avatar
 
Join Date: Nov 2016
Location: lake tahoe
Posts: 3,724
Post Thanks / Like
Thanks (Given): 673
Thanks (Received): 176
Likes (Given): 1075
Likes (Received): 1101
Garage
Quote:
Originally Posted by toroblaster View Post
I'll check the exhaust port. I have not checked the yet. The seat I made sure was in correctly. I am able to get it to idle and run at full tilt if I just partiality close the fuel valve that I put on it.
Thanks for all the ideas guys much appreciated. I'll probably try the "putting it at the curb" as a last resort. Lol.
I was thinking of soaking the Carb, would a sticky check ball cause it to flood or just not run?
Thanks.
following. had the same issue with a carb on a honda hs50 which i could not resolve. had to put a new used carb on it.

theory was the valve seat or needle valve letting too much fuel in? can that be damaged by carb cleaner? if so , that would be my fault.

"It Feels Like Beer O'Clock "
orangputeh is online now  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Snowblower Forum : Snow Blower Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome