Snowblower Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 31 Results
  1. Snowblower Repairs and Maintenance Forum
    I have been gifted an older Craftsman Snow thrower a model 536.886260. It has a Tecumseh made Craftsman engine model 143.019003. The 120 volt starter is a Tecumseh part number 37000. A number of the teeth on the 16 tooth starter gear/bendix were broken off, so I ordered a replacement gear and...
  2. Snowblower Repairs and Maintenance Forum
    This is a follow-up on a post a couple days ago about removing the auger assembly on my Craftsman 247.888530 snowblower. After removing the pulleys, the auger assembly does not come out. The splined end of the shaft is surrounded by a collar that, according to the parts diagram, is the flange...
  3. Snowblower Repairs and Maintenance Forum
    Hi, As the title of this post suggests, I'm looking for recommendations for shops that will sand blast and powder coat my auger housing (and possibly auger blades and impeller assembly). Ideally the shop is near Boston and does quality work. This past weekend I disassembled my snowblower with...
  4. Craftsman Snowblowers
    Hi, I am trying to source a set of "wheel bushings" (plastic tube / sleeve), Craftsman part number 1501138MA, but they are no longer made. These parts slide onto the axles and their OD slide inside the wheel hubs. I have checked the usual sites (propartsdirect, Jacks, Amazon, ect), but no one...
  5. Snowblowers and Snowblower Parts Wanted
    I'm looking to purchase wheel bushings, Part Number 1501138MA for my Craftsman 536.881851. Unfortunately this part is no longer made as I've searched all the usual sites online and nobody has them. It's essentially a 5.5" long plastic tube stock that takes up space between the 3/4" axles and the...
  6. New Member Introductions
    Hi there, My name is Stewart, I live in Canada. I spend a lot of time fixing cars and am now starting to work on an old snow blower I was gifted. I'm struggling to find the owners manual for a Sears Canada Model 71-52108-1. It's a craftsman 8/24. The electric start doesn't work and it runs...
  7. Craftsman Snowblowers
    I was curious has anyone ever repowered a craftsman single stage 22in with a predator engine? I’ve seen videos of it being done to a toro and ariens single stage and was curious.
  8. Craftsman Snowblowers
    Hi, I have the original 2005 tires on my snowblower (536.881851), which still hold air, but appear pretty cracked. It seems prudent to proactively replace the tires before they start to leak during a winter storm. I looked on Pro Parts Direct and it appears that the tires are only sold on new...
  9. General Snowblower Discussion
    Hello, I recently inherited an old snowblower (Craftsman 32in 10 H.P. C950-52679), and was wondering if anyone on this forum would have any information, as well as any tips on maintenance and part replacement sites. Currently, I notice two issues: 1) the axel/chain sprocket has a bit of...
  10. Snowblowers and Snowblower Parts Wanted
    Hi, I'm looking for a tall metal chute in good condition compatible with Craftsman or Murray snow blower. Below is a picture of another forum member's snow blower with the type of chute I'm looking for as well as a schematic (reference item #600) and a stock image of a new chute. Some possible...
  11. Snowblowers and Snowblower Parts for Sale
    Parting out this snowblower, message me to see if the part is still there and good. Keeping the motor but I do have one that threw a rod if you need something.
    $1 USD
  12. General Snowblower Discussion
    Hi I am a newbie to this forum, I recently bought a 1995? 536.887752 craftsman snowblower I need to do some Paint touch up does rust oleum make a color that matches. thanks in advance for your help? Gary
  13. Craftsman Snowblowers
    Hey, I recently bought a used Craftsman snowblower (Sears) and I can't find a pdf for the manual anywhere. If anyone has the same model or can find a link to the manual that would be very helpful. Briggs & Stratton engine 13hp 33 inch cut Model: C950-52313-0 Serial: 7525020531P110...
  14. Snowblower Repairs and Maintenance Forum
    Hello everyone, Seems I am the luck owner of a Craftsman snowblower with a Hilliard Autolok differential. This is a small bidirectional locking system. The wheel axels fit into splines one on each side of the assembly. I've attached two pictures, one of the assembled unit and one with the...
  15. General Snowblower Discussion
    Hi all, I bought an older sears craftsman eager 1 as a project. I underestimated how hard a friction wheel would be to come by. The rubber is completely worn off the friction wheel. I have looked high and low on the internet to find an exact replacement but it is a discontinued part, nothing...
  16. Snowblower Repairs and Maintenance Forum
    I can’t find the stator wire…is it possible to get power from the wire going into the starter?
  17. New Member Introductions
    Hi, Looking forward to some great conversations on this forum! I've got a new 24" Craftsman Snow Thrower Model 247.881732. We bought it as an 'insurance policy' after a big snow in 2016 and haven't had much snow since! LOL! Took out of box about a year ago and am just starting back to putting...
  18. Craftsman Snowblowers
    Seems no threads yet for this specific model, I guess I'm the chosen one. Here's what I picked up recently and hope to get it out there blowing snow soon. Some information I'm trying to gather for my own use (and maybe someone else's in the future) Manual? Can't find any specific to this...
  19. MTD Snowblowers
    Hi Everyone, First time posting here. I recently purchased a couple of used Craftsman snow throwers. One of them is a 2003 9Hp Tecumseh (318cc) 29 inch and the other is a supposed 2007 9Hp Tecumseh (358cc) 28 inch with EZ-Steer. The 2003 appears to need nothing but the 2007 needs minor repair...
  20. Snowblower Repairs and Maintenance Forum
    Hey all. I have a Craftsman 24" that I bought from Lowes a couple years back. Today I was cleaning the carb, but when I was taking the primer line off, the fitting broke off inside the hose. I'm still able to get the blower started, but there isn't enough fitting left to hold the line on. My...
1-20 of 31 Results
Top