[orangputeh]

I bought one at a garage sale for 50 cents...use it almost every day.

 

[Toon]

2 Ton shop crane. I have a bad back so I use the shop crane to lift the snowblower up onto my bench, so that I can work on the blower without having to be bent over. It works for me at least.

 

[Toon]

A deburring tool for quickly removing burs from drilled or sharp-edged holes. There are many brands, and they are inexpensive.

 

[Toon]

A few handy tools for the garage.

Extra long small flat screw driver, handy for carb adjustments
Extendable magnet
Slotted screw starter
Nut splitter
Right angle flat blade screw driver
Push punch
Thirst quenching tool


View attachment 196312

Finally broke down and bought a Starrett 18A spring punch. It pays to shop around. They sell for $41-$105 and anything in between. It is now resting quietly with the other punches. First tool I have owned that is made in Scotland. A very nice change.

 

[distrbd]

You can't go wrong with a genuine Starrett tool.

 

[orangputeh]

A deburring tool for quickly removing burs from drilled or sharp-edged holes. There are many brands, and they are inexpensive.
View attachment 197542

Thanks for posting this. I just bought the countersink deburring tool since i drill a lot of holes in metals. I know this will work also. watched a video.
For $10 plus extra blades may get this down the road.

 

[Toon]

Oil absorbent mats. You can see them on the floor under the tractor. They are about 18" square, about $1.50 each and keep oil from staining the concrete floor. If you have an antique car or a mower that drips a little they work great. I get mine at the local marina but they are sold in auto parts stores as well I think.

 

[Tony-chicago]

I did not know the british made tractors

 

[tabora]

Just purchased one of these fuel filters today. Truly amazing; pour water into it and NOTHING comes out. Pour contaminated gas or premix into it and the water is trapped in the top reservoir of the funnel, while pure fuel comes out the bottom.

https://www.etrailer.com/Automotive-Tools/FloTool/FTF1NC.html

 

[deezlfan]

I bought one of the original Mr Funnels. My long term opinion is that it does not work after the first half dozen uses. Fuel with ethanol or isopropyl pulls the water right through,

 

[Toon]

I did not know the british made tractors

I believe this one was made in Kentucky. If you are referring to the two pedals on the right-hand side, they are independent rear brakes. Normally they are locked together but if you unlock them and stand on one of the rear brakes, the tractor will make a tight turn to that side.
The British did make the International B275 model I believe.

 

[Tony-chicago]

Nice info.
It is a reference to leaking oil.
Same reason why little computer industry.

 

[orangputeh]

Made a tool today out of necessity.

Had to replace a broken steering lever on a Honda HSS928 snowblower. To remove the cable you have to push in the two tabs thru too tiny holes at 90 degree angles. There is no tool for this and Honda does not make a tool for this. I was able to depress the tabs from inside with a small flat screwdriver to remove the cable.

The problem is you can not do this if the lever is intact and you just need to replace/remove a cable.

I don't have a picture but i just used a tweezer and bent the ends inward at right angles for each end. You can push in tabs at same time with this.

 

[Toon]

I think what you are describing are snap ring pliers. The set I have are made by Channellock.

 

[distrbd]

I don't own this tool but it does look neat ,Princess Auto up here in Canada has it on sale for $12 ,half the price offered by Amazon :

Titan 11313 1/4-Inch Drive x 4-Inch Micro 90-Tooth Swivel Head Ratchet , Black : Amazon.ca: Tools & Home Improvement

Titan 11313 1/4-Inch Drive x 4-Inch Micro 90-Tooth Swivel Head Ratchet , Black : Amazon.ca: Tools & Home Improvement

www.amazon.ca

 

[orangputeh]

I think what you are describing are snap ring pliers. The set I have are made by Channel Lock.

no. unless they make snap ring pliers where the ends are pointed inward towards each other at 90 degrees. looked all over.

 

[Tony-chicago]

I have a set of these. I swear i have a set of inward pointing pliers. I am certain, let me go get them. Oh yeah no. Darn. I could have sworn i had a set with my various ones. But nope. I would have bet on it. Searched. Same.

 

[LenD]

Ring nose pliers??

 

[orangputeh]

Ring nose pliers??
View attachment 197858

Hey , that may work if I filed down the ends a little to fit into those tiny holes.
Thanks.

 

[Toon]

Hey , that may work if I filed down the ends a little to fit into those tiny holes.
Thanks.

Oranputeh are you talking about these access holes?

I looked at my machine closely and these are the only access points I could find.